Billet-specialties Gas Pedal 199150 Manuel d'utilisateur télécharger pdf

Billet Specialties, Inc. 500 Shawmut Avenue La Grange, Illinois 60526 PH 800.245.5382 Fax 708.588.7181 www.billetspecialties.com

JAN 10

‘55 ‘56 ‘57 (Tri-Five) Chevy

Gas Pedal #199150 / #199155

Tools Needed:

• 5/32” Allen Wrench

• Loc-tite® Thread Locker

• 3/8“ Wrench

• 77/16” Wrench

• 5/16” drill bit

Other Adjustments Include:

• Gas pedal has two axle pivot options to adjust pedal up and down on arm.

• Lower gas pedal arm can be flipped for added floor clearance.

IMPORTANT

• Check throttle operation before starting vehicle. Gas pedal

operation should be smooth and not bind in any way.

Also required but not included:

• Throttle cable and housing

1. Disconnect Battery. Disconnect throttle linkage arms from carburetor and

firewall, remove and set aside. Remove throttle linkage pivot base from firewall

with 3/8” or 7/16“ wrench, remove accelerator pedal from inside of vehicle.

Save the fasteners for later use.

2. Install the gas pedal pedestal through the firewall and into the interior of the

vehicle, secure with the two fasteners removed from the pivot base. (It is recom-

mended to apply a thin bead of RTV Silicone around the pedestal base to seal

out the elements). Tighten firmly.

3. Install the gas pedal components as shown in the illustration and finger tighten.

4. Remove carpet and or insulation from floorboard/firewall that may be in the

way of where the upper arm comes in contact.

5. Remove the clevis and nut from throttle cable (not included). Temporally

install clevis on gas pedal upper arm. Push upper arm with clevis and nut for

proper spacing against firewall and mark position. Find center and drill a small

pilot hole followed by 5/16” bit.

6. Install throttle cable (not included) per manufacturer’s instructions. Aluminum

beveled washers correct the angle of the factory firewall. They are installed on

both sides of the firewall and are held in place with the aluminum ferule and nut

supplied on the end of the throttle cable.

7. Adjust gas pedal lower arm angle to your liking and apply Loc-Tite® to the

threads of the flat head cap screw and tighten firmly. Gas pedal should not bind

in any way, Pedal operation should be smooth.

8. Replace carpet and or insulation.

FOR CONVERSION FROM FACTORY THROTTLE LINKAGE

TO CABLE STYLE THROTTLE

Gas Pedal

Upper Arm

1/4-20 x 1/2”

F.H.C.S.

Aluminum

Washer

Delrin

Bushing

Splined

Bushing

Gas Pedal

Lower Arm

E-Clips

Axle Pivot

Tension Spring

Delrin

Bushing

Gas Pedal

Pedestal

Gas Pedal Pad

Bevelled Washer

Aluminum Ferule

(Not Included)

Cable Housing

(Not Included)

Firewall

Bevelled Washer

Nut

(Not Included)

Shim

Washers

Résumé du contenu

Page 1 - Gas Pedal #199150 / #199155

Billet Specialties, Inc. 500 Shawmut Avenue La Grange, Illinois 60526 PH 800.245.5382 Fax 708.588.7181 www.billetspecialties.comJAN

Modèles reliés Gas Pedal #199155

Commentaires sur ces manuels

Pas de commentaire

Billet-specialties Gas Pedal 199150 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Billet-specialties Gas Pedal 199150. Billet Specialties Gas Pedal 199150 User Manual Manuel d'utilisatio

Résumé du contenu

Modèles reliés Gas Pedal #199155

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Billet-specialties Gas Pedal 199150